Режим работы пункта самовывоза:
Пн-пт 10:00-21:00, сб-вс 10:00-19:00.
Колл центр работает с 10 до 18 по будням.
Стабилизатор напряжения Matek UBEC DUO 4A 5-12V; 4A 5V используется в том числе для понижения напряжения с бортовой сети для питания различной электроники. Например: курсовой камеры, передатчика, сервоприводов, системы сброса груза и т.д.
UBEC DUO 4A/5-12V & 4A/5V
This device is a high-efficiency, switch-mode buck regulator with two output channels, works with 7~26Vdc Input. One output channel is capable of supplying 0~4A/5V for your RX or Flight Controller. This device also features another output channel with 4A & 5~12V(adjustable), inbuilt power switch that is operated by a spare Aux Channel, this feature can be used to power and switch on/off a wide variety of electric equipments, such as Multi-rotors Gimbals, Video Transmitters, FPV camera systems, HV Servos, navigation/landing lights, etc.
В комплекте:
Инструкция
How to Use
It is a step-down regulator, the input should be 4ce//s LiPo at least, to ensure stable output 12V.
Pay attention to the input polarity. Reversed polarity will damage the UBEC.
1. Adjust the Out-1 voltage
• Pis disconnect any attached equipments on OUT-1 before setting the voltage
• Hold the KEY 3 seconds to enter the setting of the Out-1 voltage.
• Then press KEY to choose the voltage between 5V, 6V, 7.2V, 12V (Blue LED).
• The value will be saved & exit if no action within 5 seconds.
2. Aux control function
• No Aux connection, OUT-1 Default is ON
• Connect the Aux pins to a spare Aux channel on the receiver (Two position switch ).
• Move the toggle switch to one side or another side.
• Out-1 ON, with blue LED light ON & “BeBe...BeBe"
• Out-1 OFF, with blue LED light OFF & “BeBeBeBe”
3. Input voltage monitor, Low voltage alarm & Alarm values setting
The UBEC can monitor 2-6S LiPo voltage status & notify you once the cells reach the defined voltage.
3.1 If the Input voltage is in the range of following. The UBEC will detect the cell numbers automatically when the LiPo is connected.
7.4 ~ 8.6V: 2cells LiPo 11.1-12.9V: 3cells LiPo 14.8-17.2V: 4cells LiPo 18.5-21.5V: 5cells LiPo 22.2-25.8V: 6cells LiPo
The UBEC will alarm "Be” & the voltage threshold red LED will be shown.
During the using of LiPo, UBEC will detect the voltage always.
• If the input voltage is below "threshold * cells", the alarm will be triggered with "Be. Be. Be. Be...."
• Input voltage rise again, the alarm will be suspended.
3.2 If the input voltage is out of the aforesaid range. The UBEC will alarm "Be. Be. Be" & 4 red LEDs light.
Pis check if the battery total voltage is below 3.7V*cells
3.3 The alarm threshold can be customized between 3.4V, 3.5V, 3.6V, 3.7V & OFF
• Press the KEY to set the alarm threshold. All Red LEDs go out, This function is OFF.
• The value will be saved & exit if no action within 10 seconds.
Оригинальное наименование:
Matek UBEC DUO, 4A/5~12V & 4A/5V SKU: U4A2P
Вес: | 32 г |